SOLUTIONS FOR MESH VPN • Different vendors have implemented their own • Cisco • DMVPN • Multipoint GRE Tunnel • ‘Easy’ Config • Single tunnel interface created on Hub and Spokes • Uses proprietary protocol for identifying correct GRE endpoint • OSPF (or other Dynamic Routing Protoocl) can be used to distribute routes • Juniper

Mar 08, 2018 · Site to Site VPN technique establishes a secure tunnel between two routers across public network and local networks of these routers can send and receive data through this VPN tunnel. MikroTik RouterOS offers IPsec (Internet Protocol Security) VPN Service that can be used to establish a site to site VPN tunnel between two routers. IPsec is a network protocol suite that authenticates and encrypts the packets of data send over a network. VPN (Virtual Private Network) technology provides a way of protecting informationbeingtransmittedovertheInternet,byallowinguserstoestablisha virtual private “tunnel” to securely enter an internal network, accessing resources, data and communications via an insecure network such as the Internet. www.netrotik.com Ethernet over IP (EoIP) Tunneling is a MikroTik RouterOS protocol that creates an Ethernet tunnel between two routers on top of an IP connection. A VLAN is a logical grouping that allows end users to communicate as if they were physically connected to a single isolated LAN, independent of the physical configuration of the network. 1 - my primary location (Mikrotik PPTP client) 2 - my secondary location (Mikrotik PPTP VPN server) 1 >>PPTP VPN TUNNEL >> 2 On the location 1, browsing for certain sites becomes very slow, or even impossible when the VPN tunnel is active, the loading keeps on going and going. When I disconnect the VPN tunnel, the browsing speed go back to normal. SOLUTIONS FOR MESH VPN • Different vendors have implemented their own • Cisco • DMVPN • Multipoint GRE Tunnel • ‘Easy’ Config • Single tunnel interface created on Hub and Spokes • Uses proprietary protocol for identifying correct GRE endpoint • OSPF (or other Dynamic Routing Protoocl) can be used to distribute routes • Juniper In this example, there are two locations – SiteX, which is managed by a MikroTik (SSTP server is hosted on the MikroTik) and ClientX, which is running Microsoft Windows 10. It’s important to note, that once the VPN connection is established between ClientX and SiteX, by default, all client network traffic will be routed through the VPN’s gateway.

Mar 08, 2018 · Site to Site VPN technique establishes a secure tunnel between two routers across public network and local networks of these routers can send and receive data through this VPN tunnel. MikroTik RouterOS offers IPsec (Internet Protocol Security) VPN Service that can be used to establish a site to site VPN tunnel between two routers. IPsec is a network protocol suite that authenticates and encrypts the packets of data send over a network.

PPTP VPN settings: pp select 2: pp bind tunnel1: pp always-on on: pp auth request mschap-v2: pp auth username (PPTP_ID) (PPTP_Password) ppp ipcp ipaddress on: ppp ccp type mppe-any: ip pp address 10.0.0.1/32: ip pp remote address 10.0.0.2: pptp service type server: pp enable 2: tunnel select 1: tunnel encapsulation pptp: tunnel endpoint address • To test our tunnel from the router use the ping tool and specify the interface as the inside interface(192.168.1.1). This will source the pings from 192.168.1.1 and thus will be considered interesting. This will then attempt to traverse the tunnel. GregSowell.com Since firmware version v6.45, Mikrotik routers support dialing out an IKEv2 EAP VPN tunnel to a NordVPN server. This tutorial explains how you can create an IKEv2 EAP VPN tunnel from Mikrotik router to a NordVPN server. May 29, 2016 · VPN site-to-site tunnel using IPSec setup is created in MikroTik routers between two private networks: 10.10.10.0/24 and 10.10.20.0/24; Both private networks use MikroTik router as a gateway; Each MikroTik router is behind a NAT and have private network range on WAN ports as well: 192.168.10.0/24 and 192.168.20.0/24

Ethernet over IP (EoIP) Tunneling is a MikroTik RouterOS protocol that creates an Ethernet tunnel between two routers on top of an IP connection. A VLAN is a logical grouping that allows end users to communicate as if they were physically connected to a single isolated LAN, independent of the physical configuration of the network.

SSTP Tunnel(Secure Socket Tunneling Protocol ) • Secure Socket Tunneling Protocol (SSTP) transports a PPP tunnel over a TLS 1.0 channel. The use of TLS over TCP port 443 allows SSTP to pass through virtually all firewalls and proxy servers. This tutorial assumes that the WAN interface of the Mikrotik router has a public IP address, and that your ISP does not block ipsec ports. With that out of the way, lets get started. The first step is to create a PPP Profile on the mikrotik. We will use a 192.168.102.1 for the local address (the VPN Gateway), assuming this is not already in use. We also need to add a DNS Server /ppp profile PPTP VPN settings: pp select 2: pp bind tunnel1: pp always-on on: pp auth request mschap-v2: pp auth username (PPTP_ID) (PPTP_Password) ppp ipcp ipaddress on: ppp ccp type mppe-any: ip pp address 10.0.0.1/32: ip pp remote address 10.0.0.2: pptp service type server: pp enable 2: tunnel select 1: tunnel encapsulation pptp: tunnel endpoint address • To test our tunnel from the router use the ping tool and specify the interface as the inside interface(192.168.1.1). This will source the pings from 192.168.1.1 and thus will be considered interesting. This will then attempt to traverse the tunnel. GregSowell.com Since firmware version v6.45, Mikrotik routers support dialing out an IKEv2 EAP VPN tunnel to a NordVPN server. This tutorial explains how you can create an IKEv2 EAP VPN tunnel from Mikrotik router to a NordVPN server. May 29, 2016 · VPN site-to-site tunnel using IPSec setup is created in MikroTik routers between two private networks: 10.10.10.0/24 and 10.10.20.0/24; Both private networks use MikroTik router as a gateway; Each MikroTik router is behind a NAT and have private network range on WAN ports as well: 192.168.10.0/24 and 192.168.20.0/24 Adding a site-to-site IPSec VPN-tunnel between MikroTik and SonicWall can be a hassle. I came across this issue myself, and since I couldn’t find a good tutorial, I decided to write on myself. One of those challenges I faced for an assignment was the fact I had to create an IPSec-tunnel between a SonicWall-firewall with a…